Dodge truck subwoofer installation instructions

X WAIT! Yes please! Current Stock: Quantity: Decrease Quantity: Increase Quantity:. Enter your email address to be notified when this item is back in stock. In , it was allocated to a separate company from the Dodge. Vehicle type — frame, cargo pick-up. Suspension — mixed front — torsion, rear — leaf springs , or front — spring on the models of the third generation and fully spring on the models of the fourth generation.

Drive type — all-wheel-drive or only rear-wheel drive. One of the few representatives of full-size pickups, to this day is produced in the US and Mexico plants. He made his debut in Graduation is carried out in accordance with the carrying capacity of the vehicle in pounds.

Historically, for full-size pickups, this is half a ton, three quarters and a ton the actual payload increases with each generation. Enjoy quality music with a well-maintained stereo system. I hope you will get satisfied with this article. A car subwoofer is an integral part of reforming low frequencies with a great sound system in music. It highly develops your listening experience. You might get confused before choosing it for a particular purchase.

To make it simple, you need a basic guideline for it. Here I want to share some tips to help you buy car subwoofers. Have a look at it. First of all, you need to primarily decide which subwoofer you need as there is a variety of ways for it. Once you have completely done with it, you can follow the tips I am going to mention now. The music quality is ideally determined by it. How will the sound be, loud or low?

Strong or poor? These factors mostly depend on the right size and dimension of it. If you are expecting an ideal unit, take care of the car interior space too.

Better if you know about the actual measurements before buying subs. Another essential consideration that fuels the possibility to have a suitable unit is power. Ample power is a much-needed issue with no doubt. Some models, however, feature larger speakers and high power built-in. Some of these can be bought at stores like Wal-Mart or Harbor Freight for a discount price.

Most can be bought for cheap on eBay or Amazon. It was a great deal, and has lasted well! A crimp tool shown with crimp caps is a great tool for a professional-quality installation to avoid having issues with wire connections later. I highly recommend using a cordless drill and drywall screws as they go quickly into the wood material of the box. Most subwoofers use 8 screws. Subwoofers are heavy and have a lot of vibration when in use. Installing an amplifier consists of several basic steps:.

Always be careful, and if necessary, carefully use a flat head screwdriver between gaps to help pry them off. Pull back the carpet to find room to hide your amp wire. With a flashlight, look underneath the dashboard and try to find a plastic filler plug that can be pushed out exposing a free hole you can use or a rubber seal with a factory wiring harness that goes into the engine compartment.

If you need to do this, use a punch, pointed object, or even a very strong and long screwdriver to put a hole in the rubber seal. If by chance you find a plastic hole plug like this pop it out using a screwdriver and use it as a ready-made power cable hole. That makes things MUCH easier!

Then push it through the car interior if no easier alternative is available and into the engine compartment, where you can then finally pull it through by hand and remove the power wire from it.

For best results, make a small loop on the end where you want to attach your wire and wrap it well with electrical tape to smooth over sharp edges that may snag. You may find it easier to remove the back seat and find a gap that will allow you to easily run the wire to the back. This is very straightforward. Connect a crimp ring terminal and crimp using vice grip pliers or other strong pliers or a crimp tool. Place the fuse holder near the battery with approx.

It happens! Use the ring terminal to fasten to a battery clamp bolt or stud. Use sandpaper or a wire brush to remove corrosion and expose clean metal if necessary. For the best method, use a crimp ring terminal to attach the positive wire to the battery clamp on a stud or bolt.

Be sure to remove the fuse before doing so, and install the fuse holder on the wire before connecting it to the battery. Hold in place by using zip ties to attach to nearby wiring, hoses, or brackets. Use a crimp ring terminal and secure it to the car body bare metal with a factory screw or bolt. An alternative and faster solution is to use a cordless drill and self-tapping screw to drill into the metal and fasten the ring terminal at the same time.

Otherwise using a self-tapping screw and a cordless drill make the work very quick. If the stereo in use is an aftermarket model a remote lead output wire should be available blue or blue and white.

Connect this to your remote on wire included with your kit.